Do u patch hole wall

Make sure your cuts are parallel to each other. This will allow you to attach a new piece of sheetrock to the studs.

Use a razor-knife to cut down the center of the stud. Then, make horizontal cuts with a drywall saw. This will allow you to attach your new piece of sheetrock to the stud. Cut a new piece of sheetrock the size of the hole you made. This may take some finessing if the hole is an odd shape.

Screw it to the stud on both sides using one screw every six inches or so. The sheetrock saw is better for rough in cuts. Apply a thin layer of joint compound into the seam around the patch. This layer of joint compound is simply making a bed on which the fiberglass mesh tape can be applied. Apply the sheetrock tape to all sides around the patch. The tape is pressed into the mud completely flat and the excess mud is scraped off with your trowel.

Sheetrock tape comes dry but needed to be dunked in water before it is stuck to the wall. Tape can be of any length and should be overlapped about an inch when put together. Apply mud, or joint compound, in a straight line over the length of tape used. This can be allowed to dry or a second coat can be applied immediately, so as to cover the tape. Allow to dry overnight. Once completely dry, apply a third coat of mud if you think there will be areas where the mud is not smooth.

Sand with drywall mesh sandpaper. Sand until the surface of the joints is smooth. Try to reproduce any wall texture, if necessary. When patching, one of the main problems is matching texture.

Texture can be hard to match since it is usually machine blown. To texture patches, a stiff stipple brush will often do the trick, by sticking brush in plaster and stippling on finished and dry patch.

If necessary, after it sets up a little, trowel over it to flatten high spots. Keep in mind that home improvement stores usually carry three different types of aerosol texture: knockdown, orange peel, and popcorn. Prime and then paint the entire wall. Large areas like sheet rocked whole walls and rooms should be primed really well for toughness and seal.

Follow the primer with painting the entire wall. Method 4. Gather and purchase your materials. Get your supplies together before you begin. To fix a lath and plaster wall you will need: A plaster patching compound A large joint or finishing trowel Sandpaper Coarse grade screws for wood and fine grade screws for metal. Remove loose plaster. You will need to remove all of the damaged area while making sure to not expand the damage.

Gently remove any cracked or loose plaster, moving out from the center damaged area until all the plaster you encounter is secure. Screw down any loose lath to the studs underneath. Use sheetrock screws but if the lath is cracked add wide thin washers to the screws when screwing down the lath. If some of your lath is damaged so much that it will not hold up plaster, you will need to replace it. Apply your plaster patching compound to the hole. This is the rough in coat, so the surface of the patch should be a bit below the surface of the wall and does not need to be sooth.

Allow this layer to dry for a bit, until the surface is slightly firm but not hard. The consistency of this layer of plater patch should be like peanut butter. Apply a second coat with your trowel. To patch a larger hole, you will need something to hold the spackle in place while it dries. The easiest way is to buy a wall patch kit. I used this mesh patch because I already have spackle and a putty knife, but this wall patch kit comes with everything you need.

Cut the mesh at least an inch larger than the hole. I simply taped up the whole piece of mesh up to my hole and drew an inch around the entire hole right on the mesh, then cut it out. Just long enough to get the sticky spackle started. So, stick the mesh on and start spreading spackle across it with a putty knife. Spread a thin layer of spackle then let it dry.

Repeat times, until the mesh no longer shows through. The spackle will make the area completely smooth. Adding texture is pretty easy with drywall spray texture. Just aim the aerosol can and spray. There is some over-spray, so make sure anything within a few feet of where you are spraying is covered or moved.

You might also need to dust the room afterwards, but the overspray wipes off easily. Finally, paint. Use that to cover the repaired spot. Otherwise your newly painted spot will never completely match. A butterfly patch is more durable than a patch kit, but you will need to use a piece of drywall to make it, so the process is a little more involved.

Twist or push a 1. This will allow you to hold it against the inside of the hole while you let the adhesive dry. Apply construction adhesive to the bottom and top edges of the patch. Put a zig-zag of construction adhesive along the top 1 in 2. Do the same for the bottom 1 in 2.

Insert the patch into the hole and use the screw to hold it in place while it sets. Pick up the patch by the screw and tilt it until you can insert it into the hole.

Straighten it out so it is oriented correctly and pull it towards the inside of the wall so the adhesive makes contact. Hold it in place for about 15 minutes until the adhesive has dried enough to hold it in place. Let the adhesive cure for up to 24 hours before proceeding. Leave it to cure in place at least overnight and up to 24 hours. This will ensure that the patch is secured strongly in place and will be able to support the weight of joint compound. Put a thick layer of joint compound on top of the patch to fill it in.

Use a putty knife to apply joint compound over the patch until the hole is filled to the level of the wall. Smooth out the edges so the compound overlaps onto the wall by about 1 in 2. Let the first layer of joint compound dry for 24 hours.

Leave the patch to dry for about 24 hours so it is totally cured before sanding. This is especially important since this layer is relatively thick and it will take longer to dry than a thin layer of joint compound.

Sand the joint compound smooth after it is dry. Use to grit sandpaper to smooth out the first layer of joint compound. Sand by hand or using a sanding block. Apply additional thin layers of joint compound to blend the patch in. Use a putty knife to apply another thin coat over the patch and the surrounding 1 in 2. Let it dry overnight, then sand it down with to grit sandpaper to smooth it out and blend it in with the wall.

Repeat the steps for another layer if you want to blend it in even more. According to a report by the National Association of Home Builders , Buyers, on average stay in their homes 13 years. Hardwood floors discolor, carpets wear unevenly due to furniture placement and traffic patterns. Wall art is hung with sharp things that put holes in the drywall…you get the picture I love puns! So what about that? There is no clause in the main purchase contract addressing condition of the property, however there is a commonly used addendum Form 22D which has a paragraph providing for the seller to maintain the property in the same condition as when the buyer viewed it.